How to Install an LG SIGNATURE OLED W Wallpaper TV
Mount and configure the ultra-thin LG SIGNATURE OLED W wallpaper display and companion soundbar using magnetic brackets and flat ribbon AV cabling safely.
This guide shows how to install an lg signature oled w wallpaper tv in 60-90 minutes. Start with position and level the installation guide; follow the safety notes and step checkpoints below.
Visual step map
See the full sequence before you start, then check off each step as you go.
0 of 5 steps checked
Materials and cost planner
Select the items you plan to buy, adjust any estimated price, and calculate the selected total.
Editable rough U.S. retail estimates. Estimated all listed: $221.00. Prices are planning estimates, not quotes — tax, store, brand, size and quantity will change them.
Time and finish planner
Estimate active working time from the number of steps in this guide.
Paint coverage calculator
Estimate how much paint to buy from the area you plan to cover, the number of coats and the coverage shown on the can.
Use the coverage printed on the actual product label. Rough, porous or heavily patched surfaces can use much more paint.
- Read the tools, materials, safety notes, and steps below for free.
- Tap See 20-second demo if you want to understand it first.
- Tap Start Camera Coach when you want hands-free help, or Voice-only if you do not want to use the camera.
- Allow camera and microphone. Point your phone at the work; the coach watches your progress and tells you the next step.
🧰 Required Tools & Equipment
- ✓ Stud finder
- ✓ Bubble level or laser level
- ✓ Power drill and bit set
- ✓ Phillips head screwdriver
- ✓ Tape measure
- ✓ Pencil
📦 Materials & Supplies
- ✓ LG Wallpaper TV wall bracket guide paper
- ✓ Magnetic wall mounting plate and hardware
- ✓ Flat proprietary ribbon AV cable
- ✓ Heavy-duty drywall anchors (if not into studs)
⚠️ Safety Checkpoints & Warnings
- • Never lift or maneuver the ultra-thin OLED panel alone; always use two people to prevent panel bending.
- • Verify no electrical wiring or plumbing lines run behind drill points using a multi-scanner.
- • Do not sharply pinch, bend, or crease the flat ribbon AV cable at any point during routing.
📋 Step-by-Step Guide (5 Steps)
Position and Level the Installation Guide
Locate wall studs using the stud finder and mark them with a pencil. Tape the manufacturer mounting template sheet to the wall at your desired viewing height. Use a spirit level along the template top guideline to ensure it is perfectly horizontal.
- • Template paper taped flat against the wall without wrinkles
- • Level bubble centered squarely across top reference line
- • Pencil markings clearly visible through designated screw holes
- • Relying on ceiling or floor lines instead of a bubble level
- • Mounting too high for comfortable eye-level seating viewing
Secure the Magnetic Wall Bracket
Drill pilot holes into the marked stud positions. Align the metal magnetic bracket plate over the pilot holes and drive in the mounting screws firmly. Place your level on top of the bracket to verify it remains level under full torque.
- • Metal bracket pressed flush against drywall with no gaps
- • All mounting screws fully countersunk or tight
- • Bubble remains dead center on top edge of bracket
- • Over-torquing screws and stripping the drywall or stud threading
- • Allowing bracket to rotate out of level while tightening
Route and Connect the Ribbon Cable
Plug the flat ribbon cable connector securely into the rear port of the OLED panel housing before hanging. Lay the flat cable straight downward along the wall toward the lower companion soundbar location without twisting. Keep the protective film on the cable until final positioning.
- • Ribbon connector snapped flush and locked into the panel port
- • Ribbon hangs vertically without twists or 90-degree creases
- • Forgetting to attach ribbon cable before mounting panel to the magnets
- • Bending the ribbon cable at a sharp angle, severing internal traces
Mount the Wallpaper Display to Magnetic Bracket
With two people holding opposite side edges, lift the flexible OLED panel toward the wall bracket. Hook the top mounting tabs of the panel over the top lip of the wall bracket. Slowly smooth the panel downward against the wall, allowing the magnetic surface to grip the screen uniformly.
- • Panel top tabs fully engaged into bracket slots
- • OLED screen sits completely flat against the wall with zero bulge or flex
- • Display edges run parallel to room lines and bracket
- • Attempting to lift panel solo, causing screen bending and OLED cell damage
- • Pressing directly on the screen center instead of edges
Connect Companion Soundbar and Power On
Position the companion AV soundbar on a media console directly below the display. Connect the lower end of the flat ribbon cable into the dedicated soundbar port and lock the retention clip. Plug in the power cord, connect HDMI sources, and power on the system to verify image and sound output.
- • Ribbon cable connector fully seated into companion soundbar rear terminal
- • Soundbar power indicator illuminated
- • LG setup splash screen displayed across the entire OLED panel
- • Powering on the unit with the ribbon cable only half-latched
- • Blocking top-firing Atmos speaker vents on the soundbar
Credit: inspired by an original tutorial by LG Global — watch the original on YouTube.
Don’t have everything?
- No Laser level? Standard 24-inch or 48-inch spirit bubble level
- No Multi-scanner stud finder? Magnetic stud finder to locate drywall screw heads